Fundamental Plumbing Guide for Installing a Bathtub
Fundamental Plumbing Guide for Installing a Bathtub
Blog Article
Do you find yourself trying to locate critical info concerning How to Install a Bathtub Yourself?
Mounting a bathtub isn't precisely brain surgery, yet it does call for solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old tub with a brand-new one is likewise a moderately challenging job. If the old tub is readily accessible, the project can move speedily; if you need to open up a wall surface to get rid of the old bathtub as well as position the new tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need an assistant to move out the old tub and embeded in the brand-new one. Make certain you have qualified on your own for the job as well as are comfortable trying it. As opposed to hiring a professional to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you start. Chances are you may require an expert plumber to make tube connections.
This post will certainly help you install a brand-new bath tub in your restroom if you have currently acquired a brand-new bathtub and don't need to change the setup of your previous water supply pipelines.
Your devices and material list should make up the following:
Planning for the Installation
Firstly, the supporting frame provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps device to stop pressure on the tub.
Fit the flexible faucet adapters to the bottom of both faucets using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its last setting.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is detach the water. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather troublesome because of the limited access that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from turning throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Before moving on to fit the new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Utilizing the two wood boards under its feet, place the tub in the called for setting. The wooden boards are helpful in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny points.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the bathtub up until the spirit level checks out degree.
To set up taps, fit all-time low of the outermost versatile faucet connector to the proper supply pipeline by making a compression join; then do the very same for the various other faucet.
Switch on the supply of water and also examine all joints and brand-new pipework for leakages as well as tighten them if required. Load the bathtub as well as also check the overflow outlet as well as the typical outlet for leakages.
Finally, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait until the bath tub has actually been used a minimum of when as this will certainly settle it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to prevent damages to the thread. One end of the connector fits on the plastic tail of the tap and also the other end supplies a link to the current supply pipes.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the placing opening in the bath/basin making certain that the washers remain in area in between the tap and the sink. Safeguard the faucet in position with the manufacturer supplied backnut. Once the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The previous kind needs to be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to break a rigid seal, triggering the water to permeate the wall in between the bath and also the tiling, leading to difficulties with wetness and feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and cartridges, and are capable of securing gaps up to a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched paper or soft rope. Remember to always fill the bathtub with water prior to sealing, to allow for the movement experienced when the tub remains in usage. The sealer can break fairly early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently offered on the market. It is suggested to fit the ceramic tiles making use of waterproof or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like more info about How to Install a Bathtub? Write feedback below. We would be interested to see your thoughts about this blog. In hopes that you visit us again soon. If you please set aside a second to promote this blog post if you appreciated it. Thanks a lot for your time. Please pay a visit to our blog back soon.
Address emergency plumbing promptly here. Report this page